Sklep
Store
Shop

E27 RGB + CCT

Model: BUL-01-01-04  User Manual

Safety rules
User manual
Warranty
Other informations
The LuBulb LED bulb operates on the luonOS system. To ensure proper configuration, both the LuBase central unit and the LuHome application are required.

Safety rules for product use

  • The product is intended for indoor use only.
  • Do not expose the product to extremely high or low temperatures.
  • The light source is not designed to operate in an atmosphere with increased humidity, containing aggressive vapors or chemical emissions, explosive gases, or dust.
  • The light source is designed for mounting in an Edison E27 screw socket. Any other installation (e.g., soldering wires to the E27 lamp base) is not permissible.
  • Before installing/removing the light source in the fixture, it is required to turn off the power.
  • The light source is not a product with increased mechanical durability. Do not use excessive force during its installation/removal, do not drop, and do not expose it to the influence of other forces that may cause damage or harm.
  • The light source is not a toy and should be kept out of reach of children.
  • Clean the product only with gentle, dry fabrics. Do not use chemical cleaning agents. Before cleaning, it is imperative to disconnect the power supply to the light source.
  • The light source contains non-replaceable LED diodes. In case of damage, the entire light source should be replaced with a new one.
  • Dispose of the item following the regulations for the disposal of electrical and electronic equipment.
  • Do not throw the device into regular waste.
  • Do not cover the light source. To ensure its proper durability, ensure a free flow of air.
  • Not for use with dimmers.

Technical details

Color: Milky white
Dimensions: Width.: 6 cm / Height.: 11cm
Input voltage: AC220-240V 50/60 Hz
Maximum load: 9 W
Input current: 38 mA
Standby power consumption: 0,5 W
Lumen flux: 806 lm
Color temperature: 2700K – 8000K + RGB
Color rendering index: CRI > 90
Beam angle: 200°
Operating temperature: -10°~+40°C
Storage temperature: -20°~+50°C
Dimming function: 10%~100%
Ambient humidity: max. 95% RH (no condensation)
Radio communication frequency: 2412 – 2484 MHz
Maximum radio frequency output: 13 dBm
Communication: Wi-Fi 2.4GHz
Energy class: F

User manual

Installation:

  • Ensure that the light bulb is installed according to the manufacturer’s instructions.
  • Before installation, check if the light bulb is suitable for the power source used.
  • Make sure the power is turned off during installation.

Pairing Mode – a state required to establish a connection between LuON devices and the LuBase hub.
luonOS – the software managing the smart home system and LuON devices.
LuBase – the heart of the system, the hub that allows you to control all LuON devices.
LuHome – the application for managing the smart home.
LuAiR – a radio communication system using the ESP-NOW protocol.

LuBase is required to enable LuBulb to work with HomeKit technology. See www.luon.eu for more details.

How to start pairing mode

ITo correctly install a new light bulb, you should connect it to the power source. After connecting, the light bulb will automatically activate the pairing mode, which will be indicated by glowing at maximum brightness. Then, for 10 minutes, the light bulb is in pairing mode. After this time, if necessary, you can re-enter pairing mode by disconnecting the light bulb from the power for 5 seconds and then connecting it again.

Resetting the bulb to factory settings

If you are unable to enter pairing mode, you should restore the bulb to factory settings. To reset the light bulb to factory settings, follow these steps:

  • Turn off the light bulb from the power for 2 seconds.
  • Connect the light bulb to the power for 5 seconds.
  • Disconnect the light bulb from the power for 2 seconds.
  • Connect the light bulb to the power for 5 seconds.
  • Disconnect the light bulb from the power for 2 seconds.
  • Connect the light bulb to the power for 10 seconds.
  • Disconnect the light bulb from the power for 2 seconds.
  • Connect the light bulb to the power for 5 seconds.
  • Disconnect the light bulb from the power for 2 seconds.
  • Connect the light bulb to the power for 5 seconds.
  • Disconnect the light bulb for 2 seconds.
  • After 2 seconds, connect the light bulb to the power (the light bulb has been reset to factory settings).

During pairing, the light bulb flashed green

If the light bulb flashed green during the pairing mode, it means that it has been successfully added to the luonOS system.

During pairing, the light bulb flashed red

If the light bulb flashed red during the pairing mode, it indicates that an issue occurred, and the pairing failed. In such a situation, disconnect the light bulb from the power for 5 seconds and reconnect it. Then, repeat the pairing process. If the error occurs again, reset the light bulb to factory settings and repeat the pairing process.

Bulb flashes red after pairing time has elapsed:

If, after the pairing time has elapsed, the light bulb flashed red, it may indicate the need for a reset to factory settings. Additionally, such a symptom could be caused by too big distance between the light bulb and LuBase or other devices transmitting the LuAiR signal. In this case, consider installing a device that extends the wireless communication signal between the light bulb and LuBase, or temporarily place the light bulb in a different location during pairing.

Initiating the pairing process

To initiate the pairing process of the bulb with the LuBase hub, ensure that the light bulb is within no more than 8 meters from the hub. After successful pairing, it is possible to place the light bulb at a greater distance from the hub, provided that within its range there are other devices communicating through LuAiR, which can relay the signal further.

How to pair the light bulb using the app

To add a light bulb to the luonOS system using the LuHome application, first put it in pairing mode, then click “Search for device.” Follow the instructions displayed on the LuHome application screen in the subsequent steps.

How to pair the light bulb with LuBase without using the app

To pair a light bulb with the LuBase hub without using the application, put it in pairing mode, then press and hold the reset button on LuBase for 6 seconds. If the devices are successfully paired, the light bulb and LuBase will flash green. If the devices flashes red, refer to the section “During pairing, the light bulb flashed red.”

Attention!

Devices (other than light bulbs) may require additional steps to connect them directly to the light bulb. Be sure to check the instructions for the device you want to connect to the light bulb without using the application and LuBase.

Available features

  • Utility scenes
  • Static scenes
  • Dynamic scenes
  • Last state memory in case of power outage
  • Adjusting the turn-on speed
  • Adjusting the turn-off speed
  • Adjusting the dimming speed
  • Adjusting the brightening speed
  • Adjusting the speed of color changes and color temperature changes
  • Direct connection with LuON devices

Simplified EU Declaration of Conformity

LuON S.A. hereby declares that the LuBulb light bulb model: BUL-01-01-04 complies with the directive 2014/53/UE. The full text of the EU Declaration of Conformity is available at the following address: https://luon.eu/deklaracja-zgodnosci-lubulb-e27/.

Manufacturer’s warranty

Manufacturer guarantees that the product mentioned in this warranty card is new, free from any material and workmanship defects, made of good quality materials, and meets technical-material requirements.

Warranty conditions:

  • The warranty period is 24 months from the date of purchase.
  • The manufacturer reserves the right to assess and repair the device within 14 business days from the day the device is delivered to the manufacturer.
  • Proof of purchase is essential for the user to claim free repair.

Customer’s rights:

  • Within the warranty period, the customer has the right to free device repair in case of defects.
  • The customer may request a replacement of the device with a new, defect-free product within the warranty period, only if the manufacturer determines that correcting the defect is impossible.

Warranty limitations:

  • Warranty repairs do not cover damages resulting from misuse, mechanical interference, or self-made repairs and modifications.

  • The warranty does not apply in the case of improper operation and defects resulting from the device’s operation in conditions contrary to this user manual, as well as in the case of fire, flooding, or other force majeure causing destruction or damage.

How to file a complaint:

  • In case of detecting device malfunctions, please contact the Service Department by sending an email to support@luon.eu.
  • Before sending back the device, please check if it is complete and free from mechanical damage. Then, please send the device to the following address:
    Cybernetyki Street 19B, office 402, 02-677 Warsaw.

Disposal

This device is marked in accordance with the Polish Act on Waste Electrical and Electronic Equipment and Directive WEEE 2012/19/UE with the crossed-out wheeled bin symbol. Such labeling indicates that this equipment, after the end of its use, cannot be disposed of together with other waste from households. The user is obligated to hand it over to the entities responsible for collecting used electrical and electronic equipment. Collection entities, including local collection points, stores, and municipal units, establish an appropriate system for the disposal of this equipment. Proper handling of used electrical and electronic equipment helps to avoid harmful consequences for human health and the natural environment resulting from the presence of hazardous components and improper storage and processing of such equipment.

Safety, usage

Usage

  • Do not use a damaged light bulb.
  • Do not use the light bulb in areas exposed to moisture or water.
  • Ensure that the light bulb is not covered by objects that may contribute to its overheating.

Handling

  • Do not remove any parts of the light bulb or attempt to repair it yourself.
  • Do not open the light bulb, as it may result in electric shock.
  • Do not use any chemicals or other substances that may damage the light bulb.
  • Turn off the power before attempting to change its position or removing it from the socket. 

Safety

  • Be cautious of the light bulb overheating as it may lead to damage or ignition. 
  •  Ensure that the light bulb is not too close to flammable materials. 
  • Do not leave the light bulb unattended when it is turned on. 
  • Adhere to safety principles related to connecting and using electrical devices. 
  • This equipment can be used by children aged 8 and older and by persons with reduced    physical or mental capabilities or lack of experience and knowledge, if supervision or instruction concerning the safe use of the equipment is provided to ensure that associated risks are understood. Children should not play with the equipment. Children should not perform cleaning and maintenance of the equipment without supervision.

Usage according to the intended purpose

Bulbs are designed for various applications, such as illuminating spaces or creating a specific ambiance in a room. It is important to ensure that the bulb is used in accordance with its intended purpose.

Storage

Smart bulbs should be stored in a dry, cool place, away from moisture and extreme temperatures. Store them in their original packaging. 

Maintenance

  • Turn off the smart bulb from the power source.
  • Wait a few minutes for the bulb to cool down.
  • Unscrew the bulb once it has cooled.
  • Use a soft cloth or paper towel to gently clean the bulb’s surface. Do not use any chemicals or solvents.
  • Ensure the bulb is dry, clean, and its thread is undamaged.
  • If the bulb needs replacement, disconnect it from the power and dispose of it following local waste disposal regulations.
  • If the bulb doesn’t require replacement, reconnect it to the power and check if it functions correctly.
  • Avoid turning the bulb off and on too frequently, as it may affect its lifespan.
  • In case of issues with the bulb, contact the manufacturer or supplier for technical assistance.
  • Conduct regular checks to ensure the bulb is operating correctly and free from damage.

Manufacturer

LuON S.A. al. Jana Pawła II Street 27, 00-867 Warsaw, Poland

Made in PRC